Before You Sign: How WA Mining Contractors Check Their Insurance Holds Up

Winning a principal contract on a WA mine site is the result of years of work: the crew, the equipment, the safety record, the relationships. The insurance that sits behind that contract should protect all of it. Too often it gets checked last, in the week before mobilisation, by matching policy names against a list in the contract.

That check rarely fails on paper. Where it fails is months later, when something goes wrong on site and the wording of the contract, the way the work is actually done and the wording of the policy turn out not to line up.

This guide is a pre-contract and pre-renewal check for WA mining contractors and service businesses. It assumes you already know the core policies. If you want that grounding first, start with our practical guide to insurance for mining contractors in Western Australia. This piece is about making sure that cover holds up when it is tested.

Why mining contractors insure differently

Most businesses buy insurance to protect themselves. Mining contractors also buy it to satisfy someone else. Principal contracts set minimum limits, require certain policies, and often ask you to take on risk that would otherwise sit with the principal. Remote sites, client-owned plant, shared work areas and long supply lines add exposures that a standard business pack was not built for.

The result is that two contractors with the same list of policies can be in very different positions. What matters is what each policy says, and whether it matches the contract you signed and the work your people actually do.

The cover stack, and what each layer is for

Every contractor’s program is different, but most WA mining service businesses are working with some combination of the following:

  • Public and products liability. Injury to third parties or damage to their property arising from your work, including on a client’s site.
  • Contract works or material damage. Damage to the works themselves or your own property while the job is under way.
  • Plant and equipment. Owned and hired-in machinery, including how it is valued and whether it is covered in transit and on remote sites. See our page on plant and equipment cover for mining service providers.
  • Professional indemnity. Needed if you design, specify, certify or advise, not only if you call yourself a consultant.
  • Workers’ compensation. Including how labour hire and on-hired workers are treated. See labour hire and workforce providers.
  • Motor and fleet. Including vehicles used on mine sites, where road-registered cover may not respond.
  • Business interruption. The income you lose when work stops, including from events that are not damage to your own premises.

Each layer can be in place and still leave a gap, which is why the next section matters more than this one.

Wording over price

The mistake we see most often is treating insurance as a box to tick: the contract asks for $20 million public liability, the certificate says $20 million public liability, job done. But contracts and policies can disagree on details that only surface at claim time. A few to check before you sign:

  • Who is covered. Does the contract require the principal to be noted as an interested party, or covered as an insured? They are not the same thing.
  • Contractual liability. If the contract makes you responsible for losses you would not otherwise be liable for, many liability policies will not follow you there without specific wording.
  • Client property in your care. Damage to the principal’s plant or structures you are working on is often excluded or limited under “care, custody and control” wording. Shutdown and maintenance work is where this bites hardest. See shutdown and maintenance contractors.
  • Limits and how they apply. A contract that requires a limit “per occurrence” is not satisfied by a policy written “in the aggregate” if the aggregate can be used up by one earlier claim.
  • Waivers and indemnities. Agreeing to waive your insurer’s right to recover from the principal can affect your own cover if the policy does not allow it.
  • Hired-in plant. Contracts often make you responsible for equipment you hire in. Your plant policy needs to say so too.

An illustrative example. A maintenance contractor signs a principal contract that makes them responsible for damage to client plant during a shutdown. Their liability policy excludes property in their care, custody or control. Halfway through the job, a lifting incident damages a client gearbox. The contract says the contractor pays. The policy, as worded, says it does not. Nothing about the contractor’s work was unusual; the gap was in the paperwork from day one.

That gap is fixable, often with an extension or a different policy structure, but only if it is found before the job, not after.

Two WA-specific changes worth knowing

Dust disease cover moved into workers’ compensation

Under the Workers Compensation and Injury Management Act 2023, which took effect on 1 July 2024, mining employers in WA no longer buy separate industrial disease cover from the Insurance Commission of Western Australia. For employment from 1 July 2024, that exposure is covered under the standard workers’ compensation policy the employer holds with a licensed insurer. Older industrial disease policies still respond for employment before that date (WorkCover WA, Information Sheet 49).

If your workers’ compensation program was set up before the change, it is worth confirming your insurer has your mining activities, wages and workforce correctly declared, and that nothing has fallen between the old and new arrangements.

Cyclone season and business interruption

WA’s official cyclone season runs from 1 November to 30 April, and the Pilbara coast is among the most cyclone-prone parts of Australia. For contractors, the risk is less about damage to their own premises and more about a client site closing, roads being cut, or work stopping while costs keep running. Whether your business interruption cover responds to those events depends on how it is written. We cover this in more detail in our Mining and Resources section, and in an upcoming article on cyclone-season business interruption.

Ten questions to ask your broker before you sign or renew

  1. Have you read the principal contract, not just the insurance schedule within it?
  2. Does my liability policy cover the contractual liability this contract asks me to take on?
  3. Is the principal noted, or insured, in the way the contract requires?
  4. Am I covered for damage to client property I am working on?
  5. Do my limits apply in the way the contract requires (per occurrence, or in the aggregate)?
  6. Have I agreed to waive subrogation, and does my policy allow it?
  7. Is hired-in plant covered, and on what basis is my own plant valued?
  8. Are my workers’ compensation declarations current for the work and workforce I actually have, including labour hire?
  9. Would my business interruption cover respond if a client site closed or access was cut, rather than my own premises being damaged?
  10. What has changed in my business since the last renewal (new sites, new services, new clients, new equipment), and has my program caught up?

If any of those answers is “I’m not sure”, that is the conversation to have before mobilisation, not after an incident.

Where to go next

Our Mining and Resources section covers the specific exposures for plant and equipment providers, labour hire and workforce providers, shutdown and maintenance contractors, and metal fabrication and supply chain businesses.

If you have a contract on the table or a renewal coming up, talk to us about a risk review. We read the contract, compare it with how you actually work, and show you where the wording does and does not line up, before it matters.


This article is general information only and does not take into account your objectives, financial situation or needs. Before acting, consider whether it is appropriate for you and read the relevant Product Disclosure Statement. Policy terms, conditions and exclusions vary between insurers. Delmont Group Pty Ltd (ABN 73 647 799 700) is a Corporate Authorised Representative (CAR 1285912) of Community Broker Network Pty Ltd, AFSL 233750.